How to Replace a Tub in Your Bathroom
How to Replace a Tub in Your Bathroom
Blog Article
Everybody maintains their own individual opinion involving How to Install a Bathtub.
Mounting a bathtub isn't precisely brain surgery, yet it does require solid plumbing, woodworking, and also sometimes, tiling skills. Replacing an old bath tub with a brand-new one is also a moderately tough task. If the old bathtub is readily easily accessible, the task can move quickly; if you need to open up a wall to remove the old tub as well as place the new bathtub, the task is a lot harder. In either instance, the project is within a home handyman's skills, although you will certainly require an assistant to leave the old bathtub and also set in the new one. Ensure you have qualified on your own for the work and also fit attempting it. Rather than employing a specialist to take over a halfway-completed job, it is far better to take into consideration using one before you begin. Chances are you may need a professional plumber to make tube connections.
This post will certainly assist you set up a brand-new bath tub in your washroom if you have actually currently acquired a brand-new bathtub and also do not require to transform the setup of your previous supply of water pipes.
Your tools as well as product list ought to make up the following:
Preparing for the Installation
Firstly, the supporting frame supplied with the bath ought to be fitted (if needed) according to the maker's directions. Next off, fit the faucets or mixer to the tub. When suitable the faucet block, it is very important to make certain that if the faucet features a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets system to prevent strain on the bath tub.
Fit the adaptable faucet connectors to the bottom of the two faucets making use of 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet through the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. Ensure you use every one of the supplied washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath should currently be ready to be suited its final position.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your setup, then the first thing you need to do is detach the water supply. After doing so, switch on the taps to drain pipes any water continuing to be in the system. The process of removing the existing faucets can be quite troublesome due to the limited access that is usually the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipelines to the taps. Have a towel prepared for the remaining water that will certainly come from the pipelines. When the supply pipelines have been removed, make use of the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from turning throughout this process. When the taps have actually been removed, the holes in the bath/basin will certainly have to be cleaned up of any old securing compound.
Prior to moving on to fit the brand-new taps, contrast the pipe links on the old faucets to the new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new taps to fit.
Mounting the Tub
Making use of the two wood boards under its feet, place the tub in the required setting. The wood boards are valuable in equally spreading the weight of the bath tub over the area of the boards rather than concentrating all the weight onto four little points.
The next objective is to ensure that the tub is leveled all round. This can be attained by inspecting the level and changing the feet on the bath tub until the spirit level reviews level.
To set up faucets, fit the bottom of the furthest adaptable tap port to the proper supply pipe by making a compression join; after that do the very same for the other tap.
Activate the water supply as well as inspect all joints and also brand-new pipework for leaks and tighten them if required. Fill up the tub and likewise inspect the overflow electrical outlet and also the regular electrical outlet for leakages.
Finally, fix the bathroom paneling as defined in the manufacturer's instruction manual. Tiling and sealing around the tub ought to wait up until the tub has actually been used at least once as this will resolve it right into its last placement.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic port to avoid damages to the string. One end of the port fits on the plastic tail of the tap and the other end offers a connection to the existing supply pipelines.
If you require to fit a monobloc, after that you will certainly call for lowering couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, position the tap in the installing hole in the bath/basin guaranteeing that the washers remain in location in between the faucet as well as the sink. Protect the faucet in place with the maker supplied backnut. When the faucet is safely in place, the supply pipes can be linked to the tails of the taps. The taps can either be connected by using corrugated copper piping or with normal tap adapters. The previous kind needs to be attached to the faucet finishes first, tightening only by hand. The supply pipes can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Tub
In the area where the bath meets the floor tile, it is essential to secure the joins with a silicone rubber caulking. This is essential as the fitting can move sufficient to fracture an inflexible seal, triggering the water to permeate the wall in between the bathroom as well as the tiling, resulting in problems with dampness and also feasible leakages to the ceiling below.
You can choose from a selection of coloured sealers to blend in your fixtures and installations. They are offered in tubes and cartridges, and can sealing gaps up to a size of 3mm (1/8 inch). If you have a larger gap to load, you can load it with twists of drenched paper or soft rope. Keep in mind to always load the tub with water before securing, to enable the movement experienced when the bathtub remains in use. The sealer can split fairly very early if you do not take into account this activity before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are additionally quickly available on the marketplace. It is advisable to fit the ceramic tiles using water-resistant or water-proof adhesive and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I came across that write up on Tools You Need to Install a New Bathtub when perusing the web. Do you know another person who is enthusiastic about the subject? Feel free to share it. I thank you for reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Book An Estimate Now Report this page